peace
Site Admin
Joined: 12 Feb 2007
Posts: 192
|
|
| Post subject: TriPulsar instructions for use |
 Posted: Mon May 21, 2007 4:17 am |
|
TriPulsar
This information here is based on Dr. Bob Becks’ original protocol for using the blood electrifier and colloidal silver generator.
According to his research, he found a way to kill all known viruses with a four pronged treatment: 1) Ozonated water 2) Colloidal silver water 3) blood purifier (zapping device) 4) Magnetic pulsar.
This unit is made to the exact specifications designed by Dr. Bob Beck. It can be used in for numbers #2, #3 and #4 as listed above. As all people are different, results may vary. These units are most effective when used according to Dr. Bob Becks’ protocol. Nothing is guaranteed. Put simply, the closer you match Becks protocol, the better results you may achieve.
Research from Harvard, MIT and Albert Einstein College of Medicine has shown that micro currents are known to eliminate viruses, parasites, fungi, bacteria and pathogens in the blood. This unit emits those same micro currents.
It has been a long known fact, that silver colloids greatly assist in eliminating known pathogens and prevents opportunistic infections.
Making Colloidal Silver Water
Colloidal Silver water is very susceptible to light and temperature change, so it must be kept in dark amber bottles or opaque containers. A stable room temperature environment is ideal.
The silver rods supplied are 99.99% pure silver. A higher grade of silver of 99.999% purity can be used. Lower grade silver or sterling silver will contain nickel which is toxic and must
Not be used.
Turn switch to “CSG”. When the lead (the one with alligator clips that connect the silver rods) is plugged in, it will switch the zapper and intensity button OFF. This is a direct positive current. The LED will not light up when this is plugged in.
Connect the silver rods to the alligator clips; plug this lead to the “output” socket on the main device. Place the silver rods over the top lip of the glass (see fig. 1).
Use 250ml distilled water. Place the silver rods 4-5cm apart. Keep them parallel and do not let them touch (otherwise it is likely to “short” the unit out and render it ineffective).
Distilled water is non-conductive, so it is necessary to create conductivity in the water.
This can be obtained by either placing a few grains of sea salt in the water, two to three drops of lemon juice or raising the water temperature to “luke-warm”.
One rod will emit bubbles, the other, a grey mist.
Generate for 5-15 minutes.
Zapping
Before zapping, it is very important to eliminate ALL herbs (including garlic), dietary supplements, alcohol, recreational drugs and medications. Stop taking these at least 24 hours prior to using the zapper (preferably 4-7 days before zapping). You may then take medicine or vitamins straight AFTER zapping. This is because zapping can allow medicines, drugs and herbs to enter the body’s’ cells and it can actually magnify their effect 20-30 times so while you are zapping with these in your body, the supplements are amplified dramatically.
Zapping times can vary between 15 minutes a day to 2 hours a day.
It is very important to drink at least 3-4 glasses of filtered or purified water (even distilled water) during the zapping process. This will help to flush your system and allow “detoxification” to occur. YOU MUST DRINK PLENTY OF WATER WHILE ZAPPING or you will not detoxify your body correctly.
If you feel unwell after zapping reduce the zapping time. The “unwell” feeling is the body detoxifying. This is a good sign but it is not necessary to feel unwell every time you zap.
Switch to “Zapper”, The LED will flash red/green. The “intensity” knob will adjust the brightness of the LED and adjust the “tingling” feeling emitting from the electrodes.
Set this to a comfortable level. Do NOT turn up fully clockwise and use. Turn knob fully off or anti-clockwise and gradually turn up to find your comfortable feeling. You will feel a gentle tingling effect. As the zapping session proceeds, you may not notice the tingling; you can then gradually turn it up until you feel it again. Once the electrode lead is plugged in the LED will turn OFF.
It is important to place the electrodes correctly otherwise zapping will not be effective.
Insert the silver electrodes into the cotton sleeves. Mix up a small amount of purified water with sea salt and wet the cotton sleeves with this solution. This is a saline solution which will aid with conductivity between the electrodes and your skin. Do not place the electrodes on bare skin as this may burn or give an uncomfortable feeling to the skin.
See figure 2 for correct placement.
Magnetic Pulsar
This is part 4 of Dr. Bob Becks’ protocol.
It is best to use the Magnetic Pulsar 15-30 minutes before the zapper and 2 hours before or after taking colloidal silver water.
The purpose of this treatment is to disable microbes that are not floating around the bloodstream but are ‘hiding’ in the lymph system, root canals, the stomach area etc.
Use the device by placing it around these areas or any area where damaging cells survive.
By not plugging the lead into the device it remains in Pulsar mode. Switch the unit on (towards zapper) and place over desired area. Begin by pulsing for 5 minutes on each area starting with the lymph nodes and organs. Then use on areas of the body which are inflamed, swelling or congested and finally, areas of known diseased cells or areas of concentrated infected cells. Each day you can increase the pulsing time to 10 minutes on each area – not exceeding 60 minutes total.
Again, follow Dr. Bob Becks’ protocol for specific instructions |
|
